Author Topic: CVR Electric Water Pump Adapters (Read 13502 times)

jayb · « **on:** February 28, 2013, 08:46:53 PM »

Now for sale are machined billet aluminum adapters to allow the CVR Proflo Extreme electric water pump to bolt onto FE engines. For more information, or to purchase a set of these adapters, please visit the link below:

http://www.fepower.net/Products/cvradapt.html

The long, drawn out (

) process for getting them designed and machined is covered in this thread on the technical forum:

http://fepower.net/simplemachinesforum/index.php?topic=706.0

Pricing is as follows:

Part #12001 - Plain set, no mounting points for factory brackets: $145.00 per set plus shipping
Part #12002 - Set with mounting points for factory alternator brackets: $185.00 per set plus shipping
Part #12003 - Set with mounting points for factory alternator brackets and factory power steering pump brackets: $225.00 per set plus shipping
Part #12004 - Set with mounting points for factory alternator brackets, to fit the SOHC engine: $185.00 per set plus shipping

Thanks for all the support on this project - Jay

afret · « **Reply #1 on:** February 28, 2013, 09:06:53 PM »

Order sent. Thanks!

jayb · « **Reply #2 on:** February 28, 2013, 09:36:53 PM »

Thank-you, Earl. You are using them on an aftermarket block, correct? Is it OK if I send you one with the round O-ring on the right side? I checked the fit on my Shelby and Pond blocks, and the O-ring fits around the water jacket opening with no problem.

afret · « **Reply #3 on:** February 28, 2013, 10:20:50 PM »

I'm using them on a Genesis with round holes so that would be fine. I should have mentioned that on my order. Sorry about that.

jayb · « **Reply #4 on:** February 28, 2013, 10:29:42 PM »

No problem, and thanks. I'll get them out in the morning.

fetorino · « **Reply #5 on:** March 01, 2013, 06:21:41 PM »

Jay

Thanks again for the effort on these. I see my set got delivered. Just what every well dressed TP needs.

Rob

fe66comet · « **Reply #6 on:** July 06, 2014, 09:51:03 PM »

Hey Jay I den a message the other day was just wondering if you got it? Thanks Jon

jayb · « **Reply #7 on:** July 06, 2014, 10:10:33 PM »

Just got it and sent you a PM, Jon - Jay

fekbmax · « **Reply #8 on:** December 20, 2015, 11:17:42 PM »

Do these allow the pump to clear belt drives or will spacer's be needed and are they also available ?

jayb · « **Reply #9 on:** December 21, 2015, 12:58:30 AM »

You mean timing belt drives like the Danny Bee, right? I haven't specifically checked that, but the Danny Bee belt drive fits behind the factory water pump, and the CVR pump plus the adapters has the same clearance in the back as the factory water pump, so I'm pretty sure there would be no problem - Jay

fekbmax · « **Reply #10 on:** December 21, 2015, 12:41:20 PM »

Thanks jay, I have acquired a nice used DannyBee that just needs a belt and a tensioner and some hardware. Everything I need is available from DannyBee. I'm thinking of using it or replacing the needed parts and re selling it. I'll have plenty of room out front and was thinking that if I did use spacer's it would allow more room for making adjustments. It's good to know that the pump would fit without them though. You still have some of the basic adapters in stock m guessing ?

jayb · « **Reply #11 on:** December 21, 2015, 02:01:59 PM »

I just finished up another production batch and have them all in stock - Jay

fekbmax · « **Reply #12 on:** February 19, 2016, 10:42:51 PM »

Do you have the cvr pumps as well or just the adaptors ? I'll be making an order in a couple weeks. Just trying to save a few bucks, if you don't have the pumps would you recommend me going straight through CVR website or through sumitt/jegs ?

jayb · « **Reply #13 on:** February 20, 2016, 12:14:51 AM »

I don't have the pumps and inlet tubes here, Keith. I'd go through Summit or Jegs to get them, I think that's cheaper than going direct to CVR - Jay

thatdarncat · « **Reply #14 on:** February 20, 2016, 12:35:14 AM »

Just as an FYI, of the two big mail order stores I've only seen the CVR products at Summit. I don't think Jegs carries them.

fekbmax · « **Reply #15 on:** February 20, 2016, 06:56:53 AM »

Thanks guys..

mn67 · « **Reply #16 on:** April 06, 2016, 09:13:14 AM »

Jay,
Adapters arrived this morning. I must say they are really nice thank you.

Mike

jayb · « **Reply #17 on:** April 06, 2016, 03:53:23 PM »

Your welcome, Mike, good luck on the project!

fekbmax · « **Reply #18 on:** July 03, 2016, 11:45:30 PM »

Do they make a -16an hose adapter for the CVR pump ?

thatdarncat · « **Reply #19 on:** July 04, 2016, 12:09:26 AM »

Yes - an assortment. Here's a link to page 3 of the CVR water pump fittings section of their catalog.

http://cvrproducts.com/2014/product-category/proflo-accessories/billet-inlet-fittings/page/3/

fekbmax · « **Reply #20 on:** July 04, 2016, 07:17:11 AM »

thanks, now why didn't i think of that ? LOL. to busy searching the big parts houses, shoulda went right to the source .

News:

Author Topic: CVR Electric Water Pump Adapters (Read 13502 times)

afret

afret

fe66comet