Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Heo

Pages: [1] 2 3 ... 220
1
FE Engine Dyno Results / Re: Lykins Motorsports 434ci Clevor, 777 hp/630 tq
« on: May 02, 2024, 03:43:28 AM »
Quote from: My427stang on May 01, 2024, 06:05:27 PM
Quote from: 1968galaxie on May 01, 2024, 05:33:57 PM
Quote from: My427stang on May 01, 2024, 04:51:29 PM
I didn't even think of that when I asked Jay if I could hang my Cleveland results, sort of an obvious and fair option.  My email to him was actually, "where did the non-FE dyno page go? " But it never existed.  Not sure why I thought it did

It does exist:
FE Power Forums »FE Power Forums »Non-FE Discussion Forum
https://fepower.net/simplemachinesforum/index.php?board=3.0

There is no dyno section there, period, and I contacted the forum owner directly before I posted.  If he would have said put it there, I would have put it there.  As much as I would like to push back, you get a little credit, that is a good idea.

Nobody is fighting you here, you seem to think that Jay saying it's OK beforehand wasn't enough, and you keep changing what you are upset about... I have no beef with any of this, but you can't argue what the forum owner says, it isn't my forum and it isn't yours....just let it go.

BTW - On edit - Go look at the forum you are trying to keep pure...3 Y-blocks, 1 Boss, and 3 MELs before our Clevelands showed up.  This isn't new
   What he said,,,, stop throwing sand at each other, if Jay okayed it then its okay nobody is forced to read it

2
FE Technical Forum / Re: What is your engine prep for a long sitting engine?
« on: April 22, 2024, 12:51:57 AM »
Same for them, they had blocks and cranks and other bare castiron/steel parts laying around in the garage
that had not rusted. So what happened i dont know ...no rust in the crankcase or under the valvecovers
just the liftervalley. And she had not had any coolant in the engine

3
FE Technical Forum / Re: What is your engine prep for a long sitting engine?
« on: April 20, 2024, 08:40:59 AM »
She rebuilt the engine herself so no switch or nothing like that. just sitting assembled in a heated garage
in the car and to top that of we have realy low humidity here. Some way condensation must have gathered
under the intake and rusted the unoiled castiron

4
FE Technical Forum / Re: What is your engine prep for a long sitting engine?
« on: April 19, 2024, 04:14:45 PM »
I can tell you a story about an engine sitting for 5-6 years if i remember right.
I have a female friend that did a beautyful restoration of a 67 Camaro RS SS
Full rebuilt 327 never started for 5-6 years since rebuild stored in heated garage
She gave me a call and asked if i could come by. They had some problem adjusting
the valves after they had broke in the cam
I Went there and found out it was solid lifters on a hydraulic cam! Kit from Comp Cams ???
So she removed the intake to change lifters, the liftervalley was covered in real coarse rust,
the oil was full with rustflakes like a coarse sand, oilpump was shot the bearings was junk
That was an engine never started before the camebreak in so probably was no oilcoat inside
But stored in a garage with 20 degres celsius the whole time,no water in the cooling system
So i would atleast lift the intake and have a look


5
Member Projects / Re: Shelby stocker
« on: April 17, 2024, 01:59:22 PM »
Hey Mike, Incredible beautyful car,,,,Incredible beautyful :o

6
Non-FE Discussion Forum / interesting
« on: April 08, 2024, 02:28:06 PM »
https://www.youtube.com/watch?v=hxrXRA7zjRE
I love 8 stacks

7
Private Classifieds / Re: Beautiful NOS '64 Galaxie Headlight Housings, full set
« on: April 01, 2024, 12:35:40 PM »
Damned, to late on the ball had needed those :'(

8
Non-FE Discussion Forum / More interesting Fords
« on: March 24, 2024, 06:47:26 PM »
https://www.youtube.com/watch?v=EoQ7J3OcnRA

9
Non-FE Discussion Forum / Re: interesting
« on: March 23, 2024, 04:33:42 PM »
I think it have been among the worst winter i can remember. Cold with overcast for weeks in a row
verry few days with clear sky -40 for several days in a row.
Usualy march is clear sky with cold nights and sunny days with abow freezing but not this year
Thursday was sunny with +6 celsius but the wegot overcast with 10 inch of snow this weekend

Funny thing, today when i came home from the shop the snow was shoveled from the front porsh
I thought the wife had done it but....It was Jehovahs Witnesses that had done it :o ;D ;D

10
Non-FE Discussion Forum / interesting
« on: March 22, 2024, 04:53:43 PM »
https://www.youtube.com/watch?v=tAqymesuB48&t=11s

11
Non-FE Discussion Forum / Re: 390 on the run stand (not mine)
« on: March 14, 2024, 10:09:11 AM »
Quote from: WConley on March 13, 2024, 07:39:24 PM
Quote from: Heo on March 13, 2024, 04:46:30 PM

Found picture



That's nice!!  Good detail work with the mill to get that pocket in there  :D

It was some delicate work with just a manual mill. had a old badge i cut the pins of, blacked the tips of the fins with a sharpie
scribed around the badge and milled up to the line by carefully manipulated the feeds manualy

12
FE Technical Forum / Re: oil gallery
« on: March 13, 2024, 07:16:18 PM »
I used a 3/8 extension backvards on a regular lenght tap,

13
Non-FE Discussion Forum / Re: 390 on the run stand (not mine)
« on: March 13, 2024, 04:46:30 PM »
Quote from: cammerfe on March 13, 2024, 02:14:33 PM
Interesting set of valve covers on that PI engine.

KS

Found picture


14
Non-FE Discussion Forum / Re: 390 on the run stand (not mine)
« on: March 13, 2024, 04:02:34 PM »
Quote from: cammerfe on March 13, 2024, 02:14:33 PM
Interesting set of valve covers on that PI engine.

KS

It is a set of old CalCustom that i milled down for Galaxie 390 fenderbadges somewhere i got pics with
the badges installed but cant find them right now.

15
Non-FE Discussion Forum / Re: 390 on the run stand (not mine)
« on: March 10, 2024, 01:15:27 PM »
I have built one out of squaretubing from wifes crashed horsetrailer, gaugepanel from a army surplus compressor
and radiator from a 71 LTD i scraped. just run in the cam and check for leaks befor put the engines in cars

https://www.youtube.com/shorts/b3qCOEWIrJg

Pages: [1] 2 3 ... 220