Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - DEANs427

Pages: [1] 2 3
1
Private Classifieds / Alum heads SOLD & H-S s4006b rockers package deal
« on: February 25, 2023, 07:15:06 PM »
promaxx #9170 heads, Harland-sharp rockers on Harland-sharp hd shaft #pr7001-78
w/ARP head bolts. very low run time on these parts, all have been disasembled and cleaned and checked.
valve stem heights have been corrected, all bolt hole threads chased, valve leakage checked by fluid check
1 rocker has a small knick from a push rod cup failure, cosmetic only.
head specs can be found on summit or jegs web site.
thought I would list here first.
$1750 take all
thank you, Dean
61two 245 nine305

2
Non-FE Discussion Forum / Torque conerter bolts sheered off
« on: September 04, 2022, 02:05:38 PM »
I've been doing this for a while but can't remember seeing this..
500+hp- Y block and C4 trans
without warning in 3 rd gear at 1000 ft bolts broke and engine ran free into limiter
limiter saved the engine
about 60-70 passes on combo
an ideas on this??

3
Non-FE Discussion Forum / mallory electric fuel pump 140
« on: July 19, 2021, 03:39:07 PM »
Any one out there know of a rebuilder of the mallory 140 electric fuel pump?
the electric motor part of mine died last week end, I really like these pumps but are spendy.

4
Private Classifieds / LONG PUSHRODS FOR SHELL LIFTERS
« on: January 19, 2021, 01:28:10 PM »
Smith brothers custom pushrods with very little usage time, went different route on this re-fresh
10.74 effective length, 3/16 cup and ball, .083 wall
$90 +ship
612 245 930five
dmdb1969@gmail.com

5
Private Classifieds / HOLLEY metering block 4752
« on: August 09, 2020, 08:35:22 PM »
WTB Holley metering block 4752
used on list 3410 & 3411 carbs
C5AF-BU & C5AF-BT FORD carb part numbers
may have been used on other carbs also
Dean Markuson
612 245 9305

6
Private Classifieds / FE fenderwell headers
« on: May 10, 2020, 06:30:51 PM »
custom made by "Headers by Ed" in the sixties to fit a MEL engine into a 55/56 Ford
they were used a short time and then hung in the rafters until I bought them in 2012.
I replaced the mount flange with a FE flange and modified the pipes to fit, (not much difference though). I have run these on my 56 gasser till now. there are many battle scars, welds and blemishes but still have life left in them.
equal length 1 7/8 tubes, 3" collectors
my first choice is to work a trade for a pair of cast aluminum y-block valve covers,
more pics and info at   dmdb1969@gmail.com

7
Private Classifieds / WTB 4 SPECIAL HEAD BOLTS 4 DOVE HD ROCKERS
« on: March 06, 2020, 10:46:18 AM »
Looking for the 4 special head bolts used with the Dove hd/ wide body rocker set-up.
Dean 612 245 930five

8
Non-FE Discussion Forum / Reminiscing on New Years...
« on: January 01, 2020, 12:25:11 AM »
of a simpler time...
HAPPY NEW YEAR!!

9
Good Deals! / Great deal on rocker arms fromGoeffsGalaxie
« on: December 31, 2019, 07:40:18 PM »
great deal and prompt shipping
thank you Geoff
DEANs 427

10
Private Classifieds / BAD ASS EDITION EMBLEM
« on: December 10, 2019, 10:37:48 PM »
Want to buy an emblem just like this one, vendor no longer in business.
Anybody out there have one?
Dean Markuson
612 two 45 9305

11
Private Classifieds / Wanted: comp/dove fe roller rocker arms
« on: September 01, 2019, 04:29:50 PM »
Anybody got any extra/ spare comp rockers, the blue ones that are no longer available. need 1 each of left & right off set, narrow type
would consider a whole assembly for one side if available
also need extra adjuster screws for same.
Trying to get through season before buying new complete rocker set as part of winter refresh...
612 245 9305
dmdb1969@gmail.com
Dean Markuson

12
Private Classifieds / SBF valves SOLD
« on: April 26, 2019, 08:06:53 AM »
Ferrea valves, new in box, 1.94 intake, 1.60 exhaust, 11/32 stem, 45* w/30*backcut
bought to install in Y-block heads but could not use with beehive springs.
paid $200 sell for $90, my loss your gain
dmdb1969@gmail.com
612 245 930five

13
Private Classifieds / CRANK SCRAPER-4.25 STROKER
« on: April 17, 2019, 08:41:39 PM »
FITS SCAT 4.25 CRANK W/SCAT 6.7 RODS
$25.00

14
FE Engine Dyno Results / FE-older brother Y
« on: April 09, 2019, 10:32:05 PM »
299 cubic inch
4-71 supercharger
503 hp@ 6100 rpm
450 ft/lbs@ 5000
SuperFlow WinDyn v3.2 dyno
R&R performance, Spring lake park MN

Factory ECK 292 BLOCK, .050 over, cast in 1955
Factory forged 292 hd truck crank, .020 main, .040 rods, stock stroke 3.3
Mummert forged connecting rods & push rods
Diamond blower pistons w/total seal 1.5, 1.5, 3.0 blower ring pack,
Clevite rod & main bearings, Ted Eaton special cam brg.
main bearing girdle/ scraper fabricated per Ted eaton blueprints
factory oil pump, pick-up, & truck pan
Cam& lifters by Oregon cam grinding to Ken Heard specs
Mummert aluminum cylinder heads modified to fit beehive springs & oversize ex.valves
 Harlan/sharpe 1.6 ratio roller rockers
FPP double roller timing chain
Rotating assy. balanced by Ten Eaton specialties
Factory Y block distributor converted to dura spark, curved by Faron Rhodes
Blower& drive assembly by Deans Blowers out of Washington state, old school blower
Intake manifold & crank adaptor from Y-bloke enterprizes in walla walla Australia
950 holley 3rl

15
FE Technical Forum / HOLLEY QUESTION
« on: March 19, 2019, 12:03:23 PM »
LIST 3916-1S, setting this carb up for use on top of a 4-71 supercharger, noticed main body has 1/16+ drilled passage to OUTSIDE in each venturi about 1/2 inch up from base plate !? original owner of carb said it came that way, looks factory, plan on plugging them...
opinions, comments, suggestions....

Pages: [1] 2 3